The project.

Discussion in 'General Discussions' started by Frank007301, Feb 25, 2013.

  1. Frank007301

    Frank007301

    Joined:
    Feb 8, 2013
    Messages:
    363
    Likes Received:
    1
    Location:
    Cape Town
    Hi there

    Here is my project that i am busy with. I have already ordered the tanks to fit in these areas. I need help in deciding what to use as a base(shutterply, chip board, etc.)? I will put some bricks to balance out if i have too.

    IMG_20130213_184255.jpg
    So there is going to be one tank on the right 134x80x73 and one on the left 114x50x73 all 12mm. The tank on the left will have a "waterfall" going into the tank on the right.
    IMG_20130213_184233.jpg
    There will be lights with T8 tubes hanging from the roof with chains.

    IMG_20130213_184305.jpg
    I would like any help or suggestions.

    IMG_20130213_184731.jpg


    IMG_20130213_184737.jpg

    IMG_20130213_184255.jpg

    IMG_20130213_184233.jpg

    IMG_20130213_184305.jpg

    IMG_20130213_184731.jpg

    IMG_20130213_184737.jpg
     
  2. Guest




  3. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    Are those "planters" empty/open all the way to floor level? Why not knock out the front wall of each and convert that space to cupboards for your canister filter, fish food, ferts etc...

    Then fit a marine ply top with some cross supports to take the load. That way you can cut neat holes in the ply top to run all your wiring into the cupboard section?
     
  4. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    How are you planning on the waterfall and cycling the water back to the first tank?
     
  5. richardnuss

    richardnuss

    Joined:
    Mar 19, 2010
    Messages:
    148
    Likes Received:
    3
    Location:
    Paulshof - JHB
    Looks good Frank - always wanted to try the waterfall tank set-up.

    Just watch the bases, you may want to use brick and plaster to form a stable (and level) base. Also just check that you have enough space to get you arm behind the tank on the left - jumping fish, wires / piping all need a little space.

    As planted tanks go, 730mm deep (if I read your dimensions correctly) is pretty tricky - but the plant-fundis will advise you on those specifics.

    Looking forward to seeing the project develop - keep the pics coming!
     
  6. OP
    Frank007301

    Frank007301

    Joined:
    Feb 8, 2013
    Messages:
    363
    Likes Received:
    1
    Location:
    Cape Town
    @Hawk I am going to be running the intake pipes along the specially made "light trays" on top of the tank on the left so that they end up in the tank on the right. The spray bar will be in the smaller tank.

    @Hawk again. lol. I have thought about doing that but it would be too purpose built. If i sell the house in 5 or 10 years it might be a put off to the potential buyers that don't like or want to keep fish.

    @Richradnuss I have thought about using Granite tops to place at the bottom. There is also a gap on the left that you are talking about. Also not too sure if i am going the planted route. Will keep you all posted.

    A question from my side again. Would i need to put a heater in the tank on the right or could i just put both heaters(300watt Jager) on the tank on the left? I also have 2x canister filters (1x Eheim Pro3 1200XL and a Dophin 1600) Where should i put what or could i just put both in the left side tank?
     
    Last edited by a moderator: Oct 2, 2016
  7. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    Not sure I'm following. Are you planning to use an internal filter on the left tank with outlet pipes into the right tank and again from the right tank back to the left?

    I don't think cupboards on the front of those planters are purpose built. Extra storage space is always a plus when selling. You could fit 2 lintels and then rest your granite tops on that?
     
  8. OP
    Frank007301

    Frank007301

    Joined:
    Feb 8, 2013
    Messages:
    363
    Likes Received:
    1
    Location:
    Cape Town
    I wish i could draw a picture but i suck at that. lol. I have 2x canister filters. One is an Eheim Pro3 1200XL which has 2x inlets and 1x outlet. So what i had planned is to have the 2x inlets run on top of the left tank(to stay hidden) and into the tank on the right. The outlet will only be in the left tank. The other canister is a Dophin 1600, so i was thinking that i can put that into the tank on the left too so that there are only 2x pipes in the right tank. It will look as if has a sump because there will be no heaters etc in the tank.

    I hope that better explains it.
     
  9. OP
    Frank007301

    Frank007301

    Joined:
    Feb 8, 2013
    Messages:
    363
    Likes Received:
    1
    Location:
    Cape Town
    @Hawk about the extra cupboard space. You could never use that space for the original reason again if you break it down. Just dont want to have to spend extra cash that i don't need to when i sell the house.
     
    Last edited by a moderator: Oct 2, 2016
  10. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    Ok. Got it. The reason I asked that is, what happens if 1 filter or the other fails. Also, the flows would need to match. Potentially you have the risk of running one tank dry and overflowing the 2nd. Just check if others have done this and how?
     
  11. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    Where will you store all the canisters and electrics?
     
  12. OP
    Frank007301

    Frank007301

    Joined:
    Feb 8, 2013
    Messages:
    363
    Likes Received:
    1
    Location:
    Cape Town
    @Hawk I am building a cupboard for them in the corner.

    Only the Eheims input will be in the tank on the right. If that fails there will be no filtration there at all. So there will never be a point where the tank will run dry.
     
    Last edited by a moderator: Oct 2, 2016
  13. richardnuss

    richardnuss

    Joined:
    Mar 19, 2010
    Messages:
    148
    Likes Received:
    3
    Location:
    Paulshof - JHB
    Granite will look good - just make sure there is no chance of movement, consider putting a lip in the front so it will hide the polystyrene.

    If the inlets are from the right tank, and the outlet on the left (which runs to the right via waterfall), there should be no problem having the heaters hidden as you would with a sump - just make sure there is going to be enough circulation on both tanks (no stagnant areas).

    As @Hawk mentioned, just make sure that in an electrical cut / equipement issues / blocked waterfall, that the water in the right tank can never empty completely; and the left fill up and overflow...
     
    Last edited by a moderator: Oct 2, 2016
  14. Ammar

    Ammar

    Joined:
    Aug 26, 2012
    Messages:
    2,517
    Likes Received:
    425
    Location:
    Symhurst, Germiston
    interesting project.. will follow
     
  15. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    If the tanks are not physically going to flow, one into the other, then why don't you make the 2 tank tops at the same level rather than having a step down to the right tank?
     
  16. OP
    Frank007301

    Frank007301

    Joined:
    Feb 8, 2013
    Messages:
    363
    Likes Received:
    1
    Location:
    Cape Town
    They are going to physically flowing into each other. Also if you look at the pics you can see that the one has to be higher than the other. I am not going to be building up at all. There is a step between the features.
     
  17. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    What I meant was if the step is 100mm then why not make the right tank 100mm taller so that the tops of the tanks are on the same level. You are currently going with 730mm height on both. Why not go 730mm on the left and 730mm plus the step difference on the right?
     
  18. OP
    Frank007301

    Frank007301

    Joined:
    Feb 8, 2013
    Messages:
    363
    Likes Received:
    1
    Location:
    Cape Town
    But why? Then the feature is gone.
     
  19. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    Visually I thought it would look better to have a level top but it's your project. :amuse:
     
  20. OP
    Frank007301

    Frank007301

    Joined:
    Feb 8, 2013
    Messages:
    363
    Likes Received:
    1
    Location:
    Cape Town
    I am just thinking that it would be nice to have a waterfall as a feature. If i don't like it i can always change it.
     
  21. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    If you have a physical waterfall rather than a "plumbed one tank into another" scenario it will look awesome. Enjoy dude!
     

Recent Posts

Loading...
Similar Threads - project Forum Date
5Ft, low tech,planted - African Biotope Project Members Systems Jan 19, 2026
Any interesting breeding projects happening? Breeding Dec 22, 2022
New Breeding Project Cichlids Jul 18, 2022
2m planted tank project General Discussions Jun 16, 2022
What are your new year fish projects? General Discussions Dec 20, 2021
Summer breeding project Breeding Nov 26, 2021
Project Black Beard Planted Tanks Sep 8, 2021

Share This Page