tank ideas

Discussion in 'General Discussions' started by Catfreak, Sep 12, 2012.

  1. Catfreak

    Catfreak

    Joined:
    Oct 12, 2009
    Messages:
    93
    Likes Received:
    0
    Location:
    durban
    Hi all,Would building a tank with hollow blocks be feasible.I would like to gauge the work required....seems simple in theory but.....Dimensions would be .....2m - 3m length, 1m wide, 1m high.....in essence a rectangular "pond"....but I would like a viewing panel....what can I use...and how do I water proof the internal areas.Hoping for some insight please...Also apologising in advance for the lack of punctuation,,,,,,my bb seems incapable of spacing!!
     
  2. Guest




  3. friedlandnam

    friedlandnam

    Joined:
    Oct 17, 2011
    Messages:
    106
    Likes Received:
    5
    Location:
    Stellenbosch
    You could build the tank/pond with bricks. I would however make very sure on the reinforcing that you would need to put into the construction. A 1m high wall of water is a very strong force.

    To waterproof the inside you would need to use fibreglass.

    The glass would require a recess on the inside and you would silicone it in place. The good things is that the presure from the water pushes the glass against the seal, helping in a tight seal.
     
  4. KillerBunny

    KillerBunny

    Joined:
    Jul 13, 2012
    Messages:
    182
    Likes Received:
    9
    Location:
    Krugersdorp
    I would disagree with that - Bonding a viewing window with fibreglass is a nightmare and it is unnecessary. Just paint the inside of your pond thoroughly with a good sealant. My pond is much smaller, but I have not had any issue with this approach. I'll get the name of the sealant I used for you a bit later.
     
  5. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    @Catfreak - Cast a reinforced concrete floor (100 - 200mm thick). Brick up the sides (single brick wall if it's dug into the ground otherwise look at double skin wall) and paint with pond seal (black tar looking stuff). Alternatively you could use a pond liner but there is always the chance of tearing the lining. If you are looking to fit a window then just use Marine silicone to seal the contact edges.
     
    Last edited by a moderator: Oct 2, 2016
  6. OP
    Catfreak

    Catfreak

    Joined:
    Oct 12, 2009
    Messages:
    93
    Likes Received:
    0
    Location:
    durban
    thanks guys,

    thus far i'm weighing up my options......i've measured my 3 big guys and the pangasius is sitting at 50cm, smaller guy at 45cm and my rtc is at 34cm.

    my lfs quoted 12k for a 8ft tank without any filtration....now surely from a budget viewpoint bricks and mortar will work out alot less and the extra cash can be put into filtration.

    the inflatable pool idea is also an option,,,,but my family isnt crazy about that idea as it will take up parking space for 2 cars....saw an ideal rectangular pool.
     
  7. matteffect

    matteffect

    Joined:
    Sep 5, 2011
    Messages:
    461
    Likes Received:
    20
    Location:
    Johannesburg
    Just warning you - if you go with the brick pond idea with some sorta glass or perspex pane in the front the cost of that could be rather large =D
     
  8. OP
    Catfreak

    Catfreak

    Joined:
    Oct 12, 2009
    Messages:
    93
    Likes Received:
    0
    Location:
    durban
    @ matt.

    thats what i was thinking, but im not looking at a massive viewing panel........was thinking 1m length x 50cm height or even 2 60cmx60cm panels would be ok.

    will need to price the options.

    its currently an exercise of costing everything before a decision can be made.......the pool will work a treat for a fraction of the cost.
    Metal Frame Pool dimensions of 450cm x 220cm x 84cm. It has a water capacity of 7127L...... R2000

    can't quiet match that for price.
     
  9. Zoom

    Zoom Retired Moderator

    Joined:
    Apr 13, 2009
    Messages:
    8,469
    Likes Received:
    119
    Location:
    Jhb- Fourways
    Before you go build this out of brick and cement... please contact an engineer for assistance. I see one CRITICAL problem... sounds nice and easy to lay a concrete base, and build on top of this... BUT the base and the bricks won't bond... and will move. This is where your crack will first happen. Guys that build pools out of the ground basically build the outside with brickwork, and cast the entire inside in one solid concrete shell, thus there is not joints.

    And a 1m high wall out of the ground will need to be 330mm wide... not double brick (220)
     
  10. DarylA

    DarylA

    Joined:
    Oct 18, 2010
    Messages:
    502
    Likes Received:
    17
    Location:
    Kempton Park
    If you are keen on DIY and want a monster tank on a smaller budget then consider going the plywood tank route. You will need to buy a decent piece of glass for the viewing window but it still works out far cheaper when working with large dimension tanks. Do some online research for DIY plywood tanks.
     
  11. OP
    Catfreak

    Catfreak

    Joined:
    Oct 12, 2009
    Messages:
    93
    Likes Received:
    0
    Location:
    durban
    Thanks for the feedback thus far guys,Does anyone recall the malawi tank at pta zoo.....the viewing panel was pretty solid but the brickwork looked a little "thin".... Any ideas or specs on that setup??????
     
  12. viskop ken

    viskop ken

    Joined:
    Sep 12, 2012
    Messages:
    4
    Likes Received:
    0
    Location:
    jozi
    i forget his name but the oke who heads up the aqaureium side at pta zoo will def be able to help u if u look him up
     
  13. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    Hi guys. Zoom is correct. Please don't rush out and build anthing of this magnitude without engineering advice. You are talking about 3tons of water. I just reread my earlier post and it was meant as an option and not building plans. I am an engineer and the 220 brickwall I spoke of is a retaining structure and requires more detail than "a brick wall on a concrete base".
     
  14. OP
    Catfreak

    Catfreak

    Joined:
    Oct 12, 2009
    Messages:
    93
    Likes Received:
    0
    Location:
    durban
    No problems...was doing more reading on Mfk and saw a lot of options....anyone locally built big plywood tanks?
     
  15. halo123.

    halo123.

    Joined:
    Mar 29, 2012
    Messages:
    78
    Likes Received:
    1
    Location:
    durban
    @Fonkie , @TroyFish

    Troy fish did a 1.2m
    fonkie was working on a second tank a few months ago and he promised to do a write up.
    I think fonkies is the biggest that i have heard of (in sa) , a 1000l tank.

    remember tho , the higher the tank the thicker the glass, ie 1m high you would need 17mm glass i think .

    what i would do tho is have the glass shorter than the tank, running from the top down, giving you space to hide substrate, and letting you get away with thiner glass, ie the height of the tank is 1m , but glass is 60 running down from the top.
    i still wanna build one as well , more along of the lines of a pond with a viewing pane.
    the problem i have heard of is with plecos , they can smell the wood and chew through the paint eventually.
    yeah i have a collection of plecs going so thats putting me of.

    fonkie and troyfish used 2k paint ( polyurethane paint, or automotive paint) cost wise you could do it for under 1.5 k excluding the glass , silicon does not as far as i know stick to the bitumen based pond paint. will have a look i have a pic somewhere of a pond on the bluff made of cement with a glass front , larney house , i was trying to let last year.

    i have read some where that you cant use the hollow cement bricks for a pond though!
     
    Last edited by a moderator: Oct 2, 2016
  16. OP
    Catfreak

    Catfreak

    Joined:
    Oct 12, 2009
    Messages:
    93
    Likes Received:
    0
    Location:
    durban
    Cool,I don't see the basic construction of the plywood tank as a problem. The water proofing will definitely be another story though...what products to use locally ect.The hollow block/bricks was just a thought in my head....but didn't realise what it entailed till seeing Mfk.What I need is a tank/pool large enugh for my juvenile rtc...so working from that....the tank needs to be planned.
     
  17. Fonkie

    Fonkie Nelis

    Joined:
    Sep 11, 2009
    Messages:
    213
    Likes Received:
    2
    Location:
    Potchefstroom
    Hi Guys

    My wooden tank is almost complete just wait the man who does the frame. Then hopefully start up will begin. My first tank i used 10mm glass which was framed(obviously) with a 2.5cm overlap. unfortunately the bottom corner started to leek and the glass shattered, the tank was running for a year. the new tank is the same size and i use 10mm toughed glass its 5 times stronger than normal glass and can bent a bit.

    F
     
  18. SalmonAfrica

    SalmonAfrica Batfish

    Joined:
    Dec 13, 2008
    Messages:
    3,080
    Likes Received:
    471
    Location:
    Durban
    Where will this tank/pond/plywood structure be built?

    If you're comparing costs for each, consider long-term costs as well. If this is going to be situated outdoors, additional costs in terms of insulation and heating will have to be considered. Fair enough, you are in Durban, and to some degree you can depend on ambient temperatures in the summer to stay relatively decent, but temperatures will never stay constant, and all of those fish you mentioned need tropical waters - a bare minimum of 22C I'd say. Durban winters often get as low as 15C for extended periods, and on rare occasion, lower.

    Look at insulation materials for a starter. After that, what kind of heating you may want to use - some use solar heating (I see this as somewhat reliable in Durban), or otherwise gas or electric heating (which is almost completely reliable, but expensive). These won't have to be kept on all the time. During summer you could probably leave these off, and considering the large volume of water (+ insulation) the temperature shouldn't drop too quickly either.
     

Recent Posts

Loading...
Similar Threads - tank ideas Forum Date
Ideas on what to breed in this 80L fish tank Breeding Oct 5, 2021
German blue ram tank mate ideas? Beginner Discussions May 17, 2021
Tank plans/ideas General Discussions Feb 7, 2021
My tanks and ideas Planted Tanks Dec 20, 2020
New Tank ideas General Discussions Dec 9, 2020
Ideas for a Malawi tank Species Tanks Apr 9, 2020
LED light ideas for deep planted tank General Equipment discussion Apr 18, 2019

Share This Page