Tank cracked

Discussion in 'General Discussions' started by WillemNicolaas, Jun 14, 2012.

  1. Moolis

    Moolis

    Joined:
    Sep 15, 2008
    Messages:
    1,441
    Likes Received:
    76
    Location:
    Pet Stop - Gezina Pta.
    What I mean is that the aquarium and the polystyrene must rest on a steel frame as if it is the top of a steel stand and not directly on the wooden surface.
     
  2. Guest




  3. OP
    WillemNicolaas

    WillemNicolaas

    Joined:
    Apr 8, 2012
    Messages:
    721
    Likes Received:
    10
    Location:
    George
    2012-06-14-398.jpg

    glass cracked...

    Got 3 quotes ranging from R560 -R 1061

    2012-06-14-398.jpg
     
  4. OP
    WillemNicolaas

    WillemNicolaas

    Joined:
    Apr 8, 2012
    Messages:
    721
    Likes Received:
    10
    Location:
    George


    glass cracked...

    Got 3 quotes ranging from R560 -R 1061
     
  5. DesertConvert

    DesertConvert Toad

    Joined:
    Feb 5, 2011
    Messages:
    571
    Likes Received:
    9
    Location:
    Pretoria
    Excuse my slowness (it's almost Friday after all!), but if I understand you correctly the tank with poly- base should rest directly on the steel frame of the stand, and there should be no wooden (or other) plate/base between tank & stand? Would a 10-15mm plate not aid in distributing the mass across the whole surface area instead of only at the edges & cross beams? Did I miss something in the physics?

    Apologies if this has been covered elsewhere, or if this is construed as hijacking the thread(not the intention - I think the topic is still related to the cracked tank issue).
     
  6. bylaag

    bylaag

    Joined:
    Sep 1, 2010
    Messages:
    240
    Likes Received:
    1
    Location:
    Honeydew Ridge, Roodepoort
    That's a sad pic, and I thought my 70l tank that cracked was bad. Hope you get it fixed without costing you an arm and a leg!

    DesertConvert - I agree with you that a bigger area will distribute the force better, but if the plate starts to bend or sag it could cause problems. It probably depends on what you use for the bottom plate. Any tank builder that can spread some light on what is used to support the tank?
     
  7. OP
    WillemNicolaas

    WillemNicolaas

    Joined:
    Apr 8, 2012
    Messages:
    721
    Likes Received:
    10
    Location:
    George
    Yeah i got a quote and will prob go on saturday and buy the new piece of glass and install it and let it dry over the next week... will upload pics when i get it...

    I also think with the wood story under the legs of the tank is that the wood can get pushed inwards thus causing the frame to twist just a bit and cause the glass to go under stress.

    As for the base of the frame you just need steel to spread the wait across and thick enough polystyrene to rest the tank on and that will sort out the eveness of the tank...

    For this tank i will be using a minimum of 10cm thickess leaning towards 20cm to let the tank rest on.....
     
  8. Zeiphex

    Zeiphex Axolotl

    Joined:
    Nov 16, 2011
    Messages:
    440
    Likes Received:
    10
    Location:
    Stellenbosch
    Oh man, sorry to hear :/ I've had it happen twice on my floor (and lost a LOT of fish the first time, second time there were only a bunch of platanna tadpoles and a mud crab in there (crab of course ate the tadpoles and I released him soon after. LOL )) from little tanks that weren't level.
     
  9. brent

    brent

    Joined:
    Nov 9, 2011
    Messages:
    122
    Likes Received:
    2
    Location:
    Port Elizabeth
    Sad when a tank cracks, lost a side panel of one in a move last month, something fell on it when a shelf collapsed in the new garage, was in storage so no water or fish. Interested to hear how a tank should be supported properly. Had lots over the years, albeit smaller tanks(120L) supported only by a steel frame around the bottom outer edges, luckily none ever cracked. Is it better to have the complete bottom in contact/supported with a flat surface ?
     
  10. OP
    WillemNicolaas

    WillemNicolaas

    Joined:
    Apr 8, 2012
    Messages:
    721
    Likes Received:
    10
    Location:
    George
    @Zeiphex eish man thats not good to hear. I supose and tank cracked is a big down and especially if you have fish in... Luckly mine didnt have fish in bit also still a big bummer...

    @brent Thats just bad luck with the shelf man... luckly only side panel hey...
    I would assume a total flat surcafe would be better to cover hole contact on your bigger tanks... and have thick enough polystyrene to cover the whole surface aswell. The polystyrene is very important.

    Ive seen tanks thats not standing level and then the poly takes the knock where on the one side the tank will push almoust 5 cm into the poly and the other side only like 1 cm just to even itself out. now if your glass presses on steel and not poly there.... Big problems IMO
     
    Last edited by a moderator: Oct 2, 2016
  11. Moolis

    Moolis

    Joined:
    Sep 15, 2008
    Messages:
    1,441
    Likes Received:
    76
    Location:
    Pet Stop - Gezina Pta.
    Support

    Glass bottoms of smaller aquariums (up to 4 foot) break from the sides and you need to have your support all around the outside edge of the bottom plate. If you support the whole bottom with wood the difference in expansion and contraction of the 2 materials will add loads of stress on the bottom. If you add a plate to the bottom it need to be inflexible or you can expect problems again.

    You need to manage the stress on the glass and uneven stress or specific stress points should be avoided at all costs.
    Glass and steels difference in expansion and contraction can be minimized sufficiently by adding 10mm high density polystyrene in-between.

    We have built literary 1000's of normal aquariums and 100's of large (over 300 liter) and loads of MAX aquariums (Over 1000 liter) and the only time their bottoms collapsed / cracked was when customers used steel plates, wooden sheets or the stand was uneven. OH forgot dropped stones etc.. :)
     
  12. OP
    WillemNicolaas

    WillemNicolaas

    Joined:
    Apr 8, 2012
    Messages:
    721
    Likes Received:
    10
    Location:
    George
    @Moolis Thanx for the update and clarification. think this will help lots of ppl
     
    Last edited by a moderator: Oct 2, 2016
  13. DesertConvert

    DesertConvert Toad

    Joined:
    Feb 5, 2011
    Messages:
    571
    Likes Received:
    9
    Location:
    Pretoria
    @Moolis Just to echo Willem, thank you for the explanation.
     
    Last edited by a moderator: Oct 2, 2016
  14. f-fish

    f-fish #unspecified

    Joined:
    Jun 27, 2009
    Messages:
    9,642
    Likes Received:
    2,260
    Location:
    JHB - Randburg


    I wonder how well these tanks worked in the end .. interesting stand design and support for the base .. does look nice and clean ... no idea if the design resulted in cracked tanks or not.
     
    Last edited by a moderator: Oct 1, 2016

Recent Posts

Loading...
Similar Threads - Tank cracked Forum Date
5ft tank cracked bottom panel... Newer bigger DIY help needed Anything DIY related Sep 22, 2025
Freebie: Free tank, 1 side panel and base cracked Wanted/Swop/Freebies May 25, 2021
Terrarium in a cracked tank General Off-Topic chat Sep 30, 2020
Cracked tank but light at the end of tunnel General Discussions May 20, 2020
Cracked tank General Equipment discussion Sep 4, 2019
Urgent! Cracked tank - giving away fish and plants... New members Feb 12, 2017
Tank cracked General Equipment discussion Nov 5, 2016

Share This Page