HELP needed

Discussion in 'General Discussions' started by danichigo, Dec 12, 2013.

  1. danichigo

    danichigo CA Cichlids

    Joined:
    Oct 2, 2013
    Messages:
    98
    Likes Received:
    0
    Location:
    Port Elizabeth
    Hi guys

    I have a 1.5m tank with an overflow in the corner that goes into a sump below. As you can see by the picture attached.IMG-20131109-00273.jpg The problem that I am having is that some fish like pleco's and catfish have swam over into the overflow and into the sump. Some have died after having got stuck in the pipe below. I have tried to think of ideas of what I could put there to prevent the fish from getting into the overflow but have had no luck yet. Could you guys please give me suggestions to prevent this from happening again. Finding something to go there that still allows the water to flow is easy but to attach it to the glass and wooden lid is the difficult part. Please help. Thank you

    IMG-20131109-00273.jpg
     
  2. Guest




  3. cknipe

    cknipe

    Joined:
    Aug 11, 2013
    Messages:
    196
    Likes Received:
    2
    Location:
    Bothasig, Milnerton, Western Cape
    Filter sock, sponge, a hack'ed up fish net? :D
     
  4. <<Nemo>>

    <<Nemo>>

    Joined:
    Sep 28, 2011
    Messages:
    359
    Likes Received:
    3
    Location:
    Somerset West, Helderberg
    images.jpg
    Something like this, just without the two sides.. Hope this helps...

    images.jpg
     
  5. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    Plastic or stainless steel mesh will work
     
  6. hviviers75

    hviviers75

    Joined:
    Jul 13, 2012
    Messages:
    4,789
    Likes Received:
    196
    Location:
    Brakpan
    +1 I use plastic/rubber type mesh in my internal overflow:laugh:
     
  7. OP
    danichigo

    danichigo CA Cichlids

    Joined:
    Oct 2, 2013
    Messages:
    98
    Likes Received:
    0
    Location:
    Port Elizabeth
    Thanks guys, I found plastic mesh at builders but it has too much elasticity. Any suggestions on how to attach it to the glass?
     
  8. OP
    danichigo

    danichigo CA Cichlids

    Joined:
    Oct 2, 2013
    Messages:
    98
    Likes Received:
    0
    Location:
    Port Elizabeth
    Attaching it is the main issue
     
  9. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    Silicone it to the glass or silicone a frame to the glass that you can put it into and take it out of?
     
  10. OP
    danichigo

    danichigo CA Cichlids

    Joined:
    Oct 2, 2013
    Messages:
    98
    Likes Received:
    0
    Location:
    Port Elizabeth
    The silicone could definitely work, thank you Hawk:)
     
  11. Hawk

    Hawk Clown Fish :-)

    Joined:
    May 25, 2012
    Messages:
    5,147
    Likes Received:
    80
    Location:
    Cape Town
    I love DIY (read: I'm to poor or cheap to pay money for something I can do myself) :laugh:

    Good luck and post progress/solution pics
     
  12. SalmonAfrica

    SalmonAfrica Batfish

    Joined:
    Dec 13, 2008
    Messages:
    3,080
    Likes Received:
    471
    Location:
    Durban
    +1

    You could do this during a small water change, perhaps? Lower the water level just enough to allow you to dry the area you're working with an allowing it to dry. However, I'd recommend you have another established filter running for this, as silicone does take it's time to dry and you don't want to go too long without filtration. Another alternative would be using another adhesive, although I am unfamiliar with other aquarium adhesives or their curing times.

    Regards,
     
  13. Willem

    Willem High fin Pangasius

    Joined:
    Jun 10, 2011
    Messages:
    755
    Likes Received:
    15
    Location:
    Pretoria
    What you could do when you do the water change get some air in your tank and get a small pump in your sump to circulate the water in your sump, then you should be set for at least 6 hours enough time for the silicone to dry enough not to leach.

    Regards Willem
     
  14. iamdieter

    iamdieter

    Joined:
    Jun 24, 2013
    Messages:
    321
    Likes Received:
    9
    Location:
    Benoni, South Africa
    Silicone may be difficult to work with when the surface is wet. Try Pratleys Putty (the normal setting one), it sets underwater and seems to do no harm. Extensively used in marine aquariums to secure corals to live rock.
     
  15. Jack Stone

    Jack Stone Stone Aquaics

    Joined:
    Jan 2, 2011
    Messages:
    926
    Likes Received:
    34
    Location:
    Cape Town
    I vote for the hacked up fish net idea...
    Cut the net part off, reshape the handle to grip the tank and stay in place and redo the net tightly with green 100% acrylic cotton, cut away the rest.
     
  16. eros111

    eros111

    Joined:
    Nov 3, 2012
    Messages:
    1,012
    Likes Received:
    166
    Location:
    Midrand, Johannesburg
    The cut-out teeth thing that Nemo shows the pic of works the BEST - it does not block like all the mesh type of stuff does and easy to install . You go to a florist, and get some Oasis putty - it comes on a roll, - drop you water level, dry the glass and stick the Oasis putty onto the glass and then your plastic teeth onto the putty - and it sticks like a bomb under water.
     
  17. OP
    danichigo

    danichigo CA Cichlids

    Joined:
    Oct 2, 2013
    Messages:
    98
    Likes Received:
    0
    Location:
    Port Elizabeth
    Thanks a lot guys! I got some marine silicone and some plastic mesh type material with holes big enough for efficient water flow and small enough to not allow any fish through. Will post pictures once the silicone has set.
     

Recent Posts

Loading...
Similar Threads - HELP needed Forum Date
5ft tank cracked bottom panel... Newer bigger DIY help needed Anything DIY related Sep 22, 2025
Some help needed to ID these fish General Discussions Apr 1, 2024
Racking system help needed General Discussions Feb 19, 2024
Lighting help needed Planted Tanks Oct 7, 2023
Help needed General Fish Discussions May 20, 2022
Dophin C-1600 canister filter help needed Filtration Jun 15, 2021
Co2 setup help needed General Discussions Oct 12, 2020

Share This Page