DIY inline CO2 Reactor

Discussion in 'Anything DIY related' started by WillemNicolaas, Apr 9, 2013.

  1. WillemNicolaas

    WillemNicolaas

    Joined:
    Apr 8, 2012
    Messages:
    721
    Likes Received:
    10
    Location:
    George
    Ey guys.
    So there is a lot of people that have in line reactors installed on their fish tanks, but I thought I will put a DIY out on this one as the DIY’s out there are all overseas.
    This is the parts I have used:
    400mm x 50mm PVC pipe
    50mm PVC T piece with threaded side port
    50mm 90 degree elbow (1 threaded side)
    50mm to 20mm reducers
    20mm 90 degree pipe fitting elbow with threaded side
    20mm straight pipe fitting with threaded side
    50mm end cap
    PVC weld
    Plumbing tape
    Hose clamps
    Drill + bit
    Bio balls or ceramic rings
    Sanding paper
    1.jpg
    Ok to start off I cut a piece of the 50mm PVC pipe off to make the join for the end cap and the T piece about 80mm long
    2.jpg
    Sanded down the edges of the join and also the big piece of PVC I will be using.


    3.jpg

    4.jpg
    Then apply PVC weld to the inside of the end cap and outside of the PVC join and push together
    5.jpg
    Do the same for the T piece, PVC weld in the inside and outside of the join piece.

    1.jpg

    2.jpg

    3.jpg

    4.jpg

    5.jpg
     
    Last edited: Apr 9, 2013
  2. Guest




  3. OP
    WillemNicolaas

    WillemNicolaas

    Joined:
    Apr 8, 2012
    Messages:
    721
    Likes Received:
    10
    Location:
    George
    [​IMG]
    [​IMG]
    Add PVC weld to the outside of the long PVC pipe and inside of the elbow piece and join together.
    [​IMG]

    Next you take some plumbing tape and you wrap it around the one reducer and also the straight pipe fitting and turn the reducer into the threaded T piece and pipe fitting into the reducer. (Don’t be shy with the tape and use a gorilla spanner or towel to turn those fittings in nice and tight)
    [​IMG]
    [​IMG]
    Next you add the 90 degree elbow on the other end of the PVC pipe again with PVC weld on the inside and outside respectfully.
    [​IMG]

    Add your ceramic rings or bio balls into the pipe fitting before you close it up.
    [​IMG]

    Put some tape on the other reducer and elbow pipe fitting and turn them into each other nice and tight.
    [​IMG]
    [​IMG]
    [​IMG]
    Now you have a reactor!!!
    Next we will drill a hole into the bottom part of the T piece to allow for the CO2 to enter.
    [​IMG]
    [​IMG]
    Here I had a floor and had to do a quick fix and did a proper fix the next day…
    First I added the check valve straight to the hole I drilled and PVC welded it closed, and as I installed it the check valve got a bump and broke off and water everywhere… so I added an airline tubing in the meantime.
    Next day got one of those airline tubing extension pipes and pushed that into the hole and PVC welded that to make sure no water will be pushing out there.

    Installing:
    Cut the out flow pipe of your canister filter in the middle or ¾ up and then attach the pipe from the canister to the bottom of the reactor and the pipe that has the outlet into the tank you attach to the top of the reactor.

    Make sure you leave the reactor to properly dry for 24H as the PVC weld around the co2 fitting takes a while to dry.
    You can also replace the greyish T and elbow for the normal white pvc fittings as they are cheaper than the grey ones as the grey ones are for high pressure. Place didn’t have stock so I bought these.

    Total price of the lot: +-R110

    Pearling within 30min to an hour and the O2 pumps out of the plants… No jokes.
    Hope you enjoyed and please leave so comments or ideas…
    [​IMG]
    [​IMG]
     
  4. OP
    WillemNicolaas

    WillemNicolaas

    Joined:
    Apr 8, 2012
    Messages:
    721
    Likes Received:
    10
    Location:
    George
    Big thanks to @Hilligenn for his help on this!!!
     
    Last edited: Apr 9, 2013
  5. Ryno

    Ryno Kenaal baber

    Joined:
    May 19, 2012
    Messages:
    4,022
    Likes Received:
    50
    Location:
    Pretoria
    cool so you made your outlet at the top? i build the same ones but i dril thw hole for the co2 at the top and also my outlet is at the bottom
     
  6. OP
    WillemNicolaas

    WillemNicolaas

    Joined:
    Apr 8, 2012
    Messages:
    721
    Likes Received:
    10
    Location:
    George
    Yeah mine is just swapped around. but i suppose if i swap the reactor around it will be like yours. CO2 and inlet at top.
     
  7. Ryno

    Ryno Kenaal baber

    Joined:
    May 19, 2012
    Messages:
    4,022
    Likes Received:
    50
    Location:
    Pretoria
    yep
    i noticed that it makes alot of noise shen the inlet is at the bottom
     
  8. f-fish

    f-fish #unspecified

    Joined:
    Jun 27, 2009
    Messages:
    9,642
    Likes Received:
    2,260
    Location:
    JHB - Randburg
    Are you guys trying to get all the gas to dissolve in the reactor .. seems like some commercial reactors talk about "false gas" and they have valves to allow air to escape that is not that dissolvable.
     
  9. Ryno

    Ryno Kenaal baber

    Joined:
    May 19, 2012
    Messages:
    4,022
    Likes Received:
    50
    Location:
    Pretoria
    i use my reactor and it works great. my drop checker is lime green at 2bps. its chesp to build so i have no reason to buy a commercial product. i try to make my say of dissolving as much co2 as possible. i dont like normal ceramic diffusors. it waists more co2 and dont like the mist of bubbles in the tank
     
  10. f-fish

    f-fish #unspecified

    Joined:
    Jun 27, 2009
    Messages:
    9,642
    Likes Received:
    2,260
    Location:
    JHB - Randburg
    Could not agree with you more on the ceramic stuff - waist of time, money and way too much maintenance.

    Thing that most do not realise reactors operate at a lower pressure than diffusers - they need the build-up to squeeze fin bubbles out. Higher pressure means more potential for leaks be it piping, fitting etc.

    I suppose the concern about false gas is how it could affect the reactor etc ... no clue if that is because we use industrial CO2 or fire stuff and not food grade.

    Later Ferdie
     
  11. Mitch StayC

    Mitch StayC Mitch

    Joined:
    Jul 10, 2012
    Messages:
    374
    Likes Received:
    1
    Location:
    Fourways, Johannesburg
    Sorry guys, noob question. What exactly does a reactor do? I honestly have no knowledge of this co2 stuff, lol.
     
  12. f-fish

    f-fish #unspecified

    Joined:
    Jun 27, 2009
    Messages:
    9,642
    Likes Received:
    2,260
    Location:
    JHB - Randburg
    Dissolve CO2 ... instead of me typing it all up, here is a good article Aquatic Eden - Aquascaping Aquarium Blog

    Since the 2006 article the only real addition would be the inline atomizer ... warning people get religious about a chosen CO2 diffusing strategy.

    Some examples ..

    http://www.up-aqua.com/00-dm-page/00up_dm-co2-big.jpg <---------- DIY'ers maybe a mod to your DIY reactor to produce the turbo jet ;-)
    http://www.up-aqua.com/00-dm-page/00up_co2-reactor-big.jpg
    http://www.up-aqua.com/00-dm-page/00up_co2-118-1.jpg
    http://www.up-aqua.com/00-dm-page/00dm_co2-atm-big.jpg


    I would avoid any system that uses small (sub 100g) CO2 cylinders that charges a bell like http://www.up-aqua.com/00-dm-page/00up_dm-accessory-02-big.jpg - rather go DIY CO2 at that point. Nothing beats a good CO2 setup for a planted tank.

    Later Ferdie
     
  13. OP
    WillemNicolaas

    WillemNicolaas

    Joined:
    Apr 8, 2012
    Messages:
    721
    Likes Received:
    10
    Location:
    George
    Like @f-fish said there and as you would read on the blog the reactor is there to dissolve the CO2 into the water before it reaches your tank so when the water get sprayed out into the tank the water is already mixed with co2 and it ensures that no co2 gets lost into the air via escaped bubbles. Pearling of plants is almost instant as well.

    My plants pearl so hectic that it is one long strand of O2 going up into the air from some plants...
    HTH
     
    Last edited by a moderator: Oct 2, 2016
  14. Good_Times

    Good_Times Kalahari Sandhaai

    Joined:
    Jan 18, 2012
    Messages:
    928
    Likes Received:
    6
    Location:
    Upington
    If you put on a syringe over the CO2 outlet pipe and stick the needle into the side of the canister filter outlet pipe near the canister itself, would you still have bubbles coming out or would it have enough time to dissolve?
     
  15. f-fish

    f-fish #unspecified

    Joined:
    Jun 27, 2009
    Messages:
    9,642
    Likes Received:
    2,260
    Location:
    JHB - Randburg
    So you are trying to make a venturi - I have played with the eheim on my canister. This works well for aeration .. here is a nice article fmueller.com Aeration

    I doubt pumping CO2 straight without some diffuser or surface interference like the diy diffusers would work well.

    Later Ferdie
     
    Last edited: Apr 27, 2013

Recent Posts

Loading...
Similar Threads - inline Reactor Forum Date
DIY inline heater and reactor Anything DIY related Jun 10, 2014
DIY Inline CO2 Reactor Anything DIY related Oct 2, 2013
Inline DIY heater & CO2 reactor Anything DIY related Apr 17, 2012
Inline Heater? General Equipment discussion Jul 16, 2023
Wanted: Inline heater for canister filter Wanted/Swop/Freebies Jan 15, 2022
RSS Feed Inline Aquarium Heater: Our Top Choices RSS Feeds Dec 22, 2020
Inline CO2 diffuser pressure General Equipment discussion Apr 29, 2020

Share This Page