Co2 regulator

Discussion in 'General Equipment discussion' started by quattro, Nov 17, 2014.

  1. quattro

    quattro

    Joined:
    Aug 25, 2014
    Messages:
    540
    Likes Received:
    17
    Hi
    Just want to find out if anyone has experience with these regulators. it leaked out my whole 2kg co2 bottle this weekend. So I filled it and now I've put some more thread tape on and I checked it with soapy water but can't see any leaks now. [​IMG]
     
  2. Guest




  3. Mike Roos

    Mike Roos

    Joined:
    Jun 30, 2014
    Messages:
    559
    Likes Received:
    41
    Location:
    Bronkhorstpruit dam
    pff.. Just got mine so no experience.. Maybe take it in as you should have a warranty on them?
     
  4. JCL

    JCL

    Joined:
    Oct 11, 2013
    Messages:
    452
    Likes Received:
    10
    Location:
    Cape Town
    I don't know that particular regulator and the picture doesn't tell the whole story. Where is your needle valve and bubble counter? Check for leaks around them. Then it is always a good idea to use pressure piping, not simple air tubing.
    But you dumped the whole bottle before you re-did the connections using more plumber's tape. So perhaps right now you might not have a leak, time will tell. If you still do loose CO2 then you should be able to see it using soapy water.
     
  5. OP
    quattro

    quattro

    Joined:
    Aug 25, 2014
    Messages:
    540
    Likes Received:
    17
    Gpt the 3 in 1 diffuser [​IMG]
    [​IMG]
    Needle valve adjustment screw you can see on this pic.
    Where can i buy that tubbing?
     
  6. JCL

    JCL

    Joined:
    Oct 11, 2013
    Messages:
    452
    Likes Received:
    10
    Location:
    Cape Town
    Not sure where you are based. I know where to get it in CT, but that doesn't help if you live somewhere else.
    Some LFS should have it, otherwise you could check some hydraulic/pneumatic workshops/suppliers.
    Still, even using airline, you don't dump the whole bottle of CO2 in a rush.
    So let's hope you have fixed the problem even if you haven't conciously found it.
     
  7. HennieRoux

    HennieRoux

    Joined:
    Aug 4, 2011
    Messages:
    2,431
    Likes Received:
    26
    Location:
    JHB, Roodepoort
    In general screwing regulators on should be taken with care, as i have done the same before. Not screwing them on properly will result in leaking, so just ensure that you take your time, and ensure the threads gets lined up.
     
  8. Immy

    Immy

    Joined:
    Nov 2, 2011
    Messages:
    231
    Likes Received:
    6
    Location:
    Humewood, PE
    Wow! :shock4:

    I bought an identical used regulator off the forum.

    [​IMG]

    After setup, I checked for leaks with diluted Sunlight... none.

    My 5kg was empty within two weeks!

    Suspected my trigger valve was the culprit. :shrug:

    Haven't used my pressurized system since then.


    I'm beginning to wonder if it's the solenoid... :hmm:
     
    Last edited: Nov 17, 2014
  9. ivan

    ivan Aquascaper

    Joined:
    May 24, 2011
    Messages:
    681
    Likes Received:
    15
    Location:
    Centurion
    guys try and look for leaks at the solenoid. some solenoids get stuck sometimes and will empty the tank cause there is nothing stopping the co2.
     
  10. OP
    quattro

    quattro

    Joined:
    Aug 25, 2014
    Messages:
    540
    Likes Received:
    17
    What i did now was open my bottle just 1/4 of a turn. Then on the side is a screw that looks like you use a big flat screwdriver, that I screwed in all the way and also 1/4 turn loose and checked all the pipes and i put lots of thread tape and didn't see anything. So lets hope for the best
     
  11. JCL

    JCL

    Joined:
    Oct 11, 2013
    Messages:
    452
    Likes Received:
    10
    Location:
    Cape Town
    I am not sure what you are saying here.
    -If there is a leak around the solenoid you would detect this with soap water.
    -If the solenoid is stuck in the open position, the CO2 will keep flowing until the bottle is empty. BUT, ...the rate of emptying will still be limited by the setting on the needle valve. And that will make sure that the whole CO2 content isn't dumped within a short time. If the solenoid valve stays open, CO2 will flow for 24hrs per day, roughly 3 times more than the normal average 8hrs (lighting period). In essence the bottle will be empty in 1/3 of the time.
    As a full bottle will last a relatively 'long' time, it is not possible that a stuck valve would empty the bottle in a matter of a few days.
    This I can only see happening in case of a leak somewhere.
    And in the case of a stuck valve, I would hope that the tank owner would notice that his/her CO2 bubbles are going non-stop and take remedial action.
     
  12. Immy

    Immy

    Joined:
    Nov 2, 2011
    Messages:
    231
    Likes Received:
    6
    Location:
    Humewood, PE
    @ivan and @JCL, is it possible that, while the solenoid is closed, CO2 can be escaping through the solenoid into the room, as if the 'pin' is diverting the CO2 externally?

    I only leak tested while the system was running.
     
    Last edited by a moderator: Oct 2, 2016
  13. JCL

    JCL

    Joined:
    Oct 11, 2013
    Messages:
    452
    Likes Received:
    10
    Location:
    Cape Town
    I am no expert on this but I don't see that happening.
    A valve has an inlet and an outlet, there is no path towards the outside, ie. the room.
    If I had to take a guess where the CO2 disappeared through so quickly, I would say the connection from your handvalve to your regulator.
    I don't have the same system as yours, but there should be a seal/washer inside the 'silver' nut (regulator side).
    Either your alignment wasn't very good when putting it together or the seal/washer was/is damaged. Some people say your should replace it when you refill your CO2 bottle, although oI haven't decided yet whether I agree with this. Lol
     
    Last edited by a moderator: Oct 2, 2016
  14. f-fish

    f-fish #unspecified

    Joined:
    Jun 27, 2009
    Messages:
    9,642
    Likes Received:
    2,260
    Location:
    JHB - Randburg
    I once had a leaking manifold / needle valve assembly ... see F's rescaped 4ft - Page 2

    Some locktight did the trick.

    Later Ferdie
     
    Last edited: Nov 17, 2014

Recent Posts

Loading...
Similar Threads - regulator Forum Date
Wanted: Co2 regulator or co2 setup Wanted/Swop/Freebies Nov 1, 2025
CO2 Regulator Failure General Equipment discussion Apr 10, 2023
Co2 Regulators General Equipment discussion Dec 13, 2022
CO2 regulator installation question General Equipment discussion Sep 12, 2022
Wanted: Co2 regulator Wanted/Swop/Freebies Jul 21, 2022
Wanted: Wanted: CO2 dual stage regulator Wanted/Swop/Freebies Oct 11, 2021
Seachem Alkaline Regulator - Free General Equipment discussion Oct 10, 2021

Share This Page